Geekcreit 3.5" TFT LCD Touch Screen + Protective Case + Touch Pen Kit For Raspberry Pi 3B+ / 3B/2B

( Code: P148985 )
Deal: $ 29.95
$65.95 Save: $36.00 (55%) Availability: In Stock
  • Estimated Postage:
  • Your Postcode:
  • Delivery & Handling:    $9.99
  • Direct Shipping Offer
  • * Buy now to earn 299 points
  • Combine Shipping and Save
  • Estimated Handling Time: 5 - 14 Working Days

Geekcreit 3.5" TFT LCD Touch Screen + Protective Case + Touch Pen Kit For Raspberry Pi 3B+ / 3B/2B

  • One case for two way use
  • Support cooling fan
  • Hanging hole on the bottom


Introduction :
Sometimes you use the the Raspberry Pi with 3.5 inch touchscreen , but sometime you don't use them together. In this situation , you need a case which both suitable for Raspberry Pi alone or with 3.5 inch touchscreen. This is the reason we provide this new case -- for  the people use 3.5 inch screen more convenient: When you use the touchscreen , just remove the cover board and fan; When you don't use the touchscreen , you can use the cover and fan , which become a normal case.
Please note that you can't use the 3.5 inch touchscreen and cooling fan at the sametime !


Overview :
1. One case for two way use :
​1). This case suport install 3.5 inch touchscreen , and need to remove the cover board and can't use the fan in this using way.
2). When you don't use the 3.5 inch touchscreen , it is a general case with cooling fan. 
2. Full access for Raspberry Pi : 
We leave every hole for SD card , HDMI , AV , Ethernet , USB , POE , Camera , MIPI DSI ports.
3. Support cooling fan :
You can install the cooling fan on the cover board , which make the best heat dissipation and extend the using life of Raspberry Pi.
( You can't use the 3.5 inch touchscreen and cooling fan at the sametime ! )
4. Hange hole on the bottom :
We make 2 hole on the bottom so that you can hange the case on the wall or something else .
This design is very convenient when using the 3.5 inch touchscreen.

-480×320 pixel resolution, better display.
-Driver provided (works with custom Raspbian directly).
-Supports any revision of Rasp Pi (directly-pluggable).
-Designed for Raspberry Pi, an ideal alternative solution for monitor.
-Support software keyboard (system interaction without keyboard/mouse).
-Provides the best available protection/accessibility for Model B
Protect and secure your Rasp Pi from shocks, scratches and dust.
How to install the 3.5 inch touchscreen :
1). Install the Raspberry Pi on the base board 
2). ​Please stick the pad on  the back of 3.5 inch touchscreen , then insert the 3.5 inch touchscreen on Raspberry Pi by GPIO pin correctly ( don't be malposed ) 
3). Install the cover board 


LCD Interface SPI
Touch Screen Type Resistive
Touch Screen Controller XPT2046
Colors 65536
Backlight LED
Resolution 320*480 (Pixel)
Aspect Ratio 8:5
Power Consumption TBD
Backlight Current TBD
Operating Temp. (Centigrade) TBD

Interface Definition:

1, 17 3.3V Power positive (3.3V power input)
2, 4 5V Power positive (5V power input)
3, 5, 7, 8, 10, 12, 13, 15, 16 NC NC
6, 9, 14, 20, 25 GND Ground
11 TP_IRQ Touch Panel interrupt, low level while the Touch Panel detects touching
18 LCD_RS Instruction/Data Register selection
19 LCD_SI / TP_SI SPI data input of LCD/Touch Panel
21 TP_SO SPI data output of Touch Panel
22 RST Reset
23 LCD_SCK / TP_SCK SPI clock of LCD/Touch Panel
24 LCD_CS LCD chip selection, low active
26 TP_CS Touch Panel chip selection, low active


About the system of 3.5 touch screen

The touch screen need to configure the driver for touch function , otherwise you can not use it by your own system.
Here we provide the method to configure for Raspbian system :

Step 1: Download the Raspbian IMG  
Step 2: Burn the system image
If you don't know how to do that,you can refer to the Raspberry Pi office tutorial
Step 3: Open terminal(SSH) and install the driver on RaspberryPi
(tested on RaspberryPi 3B+,3B,2B,2B+,1B,ZERO)

Drive File:
sudo rm -rf LCD-show
git clone
chmod -R 755 LCD-show
cd LCD-show/
sudo ./LCD35-show
Wait A Few Minutes, when the system reboot ok, you can see that.
Make sure your RPI connects to the internet then wait a few minutes, when the system reboot ok, you can see that.

Package Content

  • 1 x 3.5 inch Touch Screen
  • 1 x Protective Case
  • 1 x Touch Pen


What is Direct Shipping Offer?

  • The items will be shipped directly from Overseas Supplier by Air Parcel. It take 1-4 weeks (plus Handling Time) to arrive Other areas in Australia.

How is the Warranty Work?

  • Australia provide Australian local Warranty Service for all the Direct Ship Offer items

is the Tax invoice provided?

  • Yes, Tax invoice is provide for warranty purpose

How about GST and Custom Duty?

  • Following the new taxation laws, starting 1 July 2018, - all imports with an order value less than AU$1,000 has to be charged with Goods and Services Tax (GST) from buyers. Please check Australia Custom web site 
  • For an order value over AU$,1000 - Australian Custom Clearance Service is provided by Fedex or DHL, we will provide all necessary documents bundle with the parcels. Customer may need to pay GST, Duty and Custom Clearance fee for Custom Clearance.

What happen if my order get lost in transit?

  • For your peace of mind, all the item are shipped with Insurance covered, replacement will be sent to you once the parcel is confirmed missing in transit.
  • Direct Shipping Offer - is providing a platform for Australian buyers to purchase oversea item directly from oversea suppliers. will provide Australian base warranty for the item sold via direct shipping offer. Buyer remain as an importer for the items purchased from Direct Shipping Offers.

For your peace of mind - ShoppingSquare provide 30 Days Replacement Warranty** for this item